| |
|
LABORATORY PLASTIC WARE |
|
Bottom |
|
PIPETTE STAND (VERTICAL)
This is a stable, non-corrosive, detachable
stand which can hold 28 pipettes with maximum dia 14mm. The heavy base
measures 225mm in diameter and a Polypropylene coated square rod measuring
375mm in length is screwed into the base. The top disc that can fixed on the
rod has holes for holding pipettes. While the lower one has pilot holes
where the pipette tips rest and liquids drain down to the base. These discs
can be adjusted on the rod according to the length of the pipette. The
arrows provided on the discs should be kept parallel to ensure that
corresponding holes are being centered |
|
| |
|
|
PIPETTE STAND (94
PIPETTES-ROTARY)
Moulded in Polypropylene, this unique stand
holds a maximum of 94 pipettes and rotates on a central vertical axis for
convenient selection of any particular pipette. The lower rotating disc has
four concentric troughs with tapered sides and open bottoms which cradle the
pipette tips protectively and permit water drops to run off. The upper disc
has a grid pattern concentric with the bottom disc and keeps the pipettes
vertical. Liquids draining off the pipettes are retained on the top of the
stationary base by the outer ring. This stand can be easily disassembled &
reassembled. |
|
| |
|
|
PIPETTE STAND
(HORIZONTAL)
This detachable stand can hold 12 pipettes, 6 on
each side, in a horizontal position. Moulded in polypropylene, this
autoclavable stand has two sides which are attached to each other with three
metallic rods coated with polypropylene. This stand can be easily
disassembled for space saving storage.
Material Polypropylene |
|
| |
|
TEST TUBE STAND(WIRE PATTERN)
An economical substitute for wire racks, here
are these submersible autoclavable racks which are stackable when empty.
These are available in different colours and are made of a special blend of
Polypropylene that makes it sink in a water bath and maintain their
stability even in agitated water. These space saving racks can easily be
disassembled for cleaning purpose. The base is in the form of a grid with
square openings and has fold up sides and end bars that lock into rack tops.
Particulars :
13mm x 90 Tubes, 16mm x 60 Tubes, 20mm x 40 Tubes, 25mm x 24 Tubes. |
 
|
| |
|
|
TEST TUBE STAND (3 TIER)
These indegenous racks, moulded in Polypropylene
& Polycarbonate, are excellent replacement for metal and wooden racks. The
3-tier design provides clear view of the tube contents and convenient
insertion and removal of tubes. The PC rack has transparent upper and middle
plates while base and end plates are coloured where as in PP racks, every
part is coloured abd opaque. End plates are provided with spaces to lift the
rack and base plate has tapered wells with drain holes. These racks are
autoclavable and can withstand sub-freezinf temperatures.
Material : Polypropylene
Size :
13mm x 31tubes, 16mm x 31tubes, 20mm x 20tubes, 25mm x 12tubes, 13mm x
18tubes, 15mm x 18tubes, 18mm x 12tubes, 13mm x 62tubes, 16mm x 62tubes,
20mm x 40tubes. |
|
| |
|
|
TEST TUBE STAND(ROUND)
A handy, little, space saver, this circular
twelve place Polypropylene Test Tube stand has four 25mm dia holes and eight
19mm dia holes in its top plate. The base has matching hemispherical wells
and 16 vertical pins for drying tubes surrounded by a trough to catch
drippings. This autoclavable rack can be easily disassembled for cleaning
purpose. |
|
| |
|
|
FLASK STAND
Moulded in Polypropylene, this flask stand gives
a stair-like top view. Every step provides excellent support to the round
bottom flask at every point of contact. This flask stand can hold round
bottom flask up to 10 Ltr. capacity. This stackable Flask stand can also be
steam autoclaved.
Materil : Polypropylene |
|
|
TOP |
|
[<Back <] |
[>Next>] |
|
